Manufacturer Part# / Cross Reference Search
Please use this search function to find READY die set components that are equivalent to commonly used pins, bushing, ISO Springs, and Gas Springs from other manufacturers. Please Note: We believe this cross reference to be accurate. Please review the specifications to ensure the item will work in your application. Gas Spring equivalents were based on body dimensions, on contact force and stroke length.
- Designed to produce up to one million parts, ideal for most stamping dies.
- In stock lengths: 12", 24" and up to 36" long.
- Segment stock lengths to reduce your tooling budget; quick delivery.
- Benders are now less expensive than wipe tooling.
Unit of Measure
Features
Features |
N/A
|
Specifications
Rocker Diameter |
N/A 3.000 in |
Part Thickness (PT) |
N/A 0.210 to 0.250 in |
Part Height Check (PH)1 | N/A 1.160 in |
In Stock Length (X) |
N/A 12 in24 in36 in |
Minimum Length |
N/A 3.500 in |
Maximum Length (X) |
N/A 36 in |
Saddle Width (SW) |
N/A
6.875 in
![]() Loading zoom |
Saddle to Front (SF) Width |
N/A
2.750 in
![]() Loading zoom |
Saddle to Key (SK) Width |
N/A
4.125 in
![]() Loading zoom |
Saddle Height (SH) |
N/A
3.375 in
![]() Loading zoom |
Gib Length (GL) |
N/A
3.500 in
![]() Loading zoom |
Rocker Angle |
N/A 87 º |
Rocker Dimension (B) |
N/A
1.017 in
![]() Loading zoom |
Rocker Dimension (C) |
N/A 0.936 in |
Rocker Dimension (J) |
N/A 1.179 in |
Note |
N/A 12, 24" & 36" lengths in stock, 2", 2 1/2" and 3" Diameter Rockers |
Additional Information |
N/A
|
Product Code |
N/A RB |
Dart Stiffeners
Dart Stiffener Overview |
N/A
Standard darts are shown in the table below or you can specify your own angle and dowel size Darts are rolled into the part during bending, reducing springback and stiffening the part. Darts are produced using dowels through the rocker and require relief grooves in the anvil. The side angles of the darts are a function of the angle and size of the dowel. Darts are available as spcifiable extras on all READY Benders®. Darts are central on a 45° angle unless detailed. Eliminate:
![]() |
Tooth Benders
Tooth Bender Overview |
N/A
Tooth benders use special rockers to eliminate die/part interferences. Often the saddle needs to be made special without gibs in one peice. Send prints for a quotation.
![]() |
Over Square Bends
Over Square Bend Overview |
N/A
The READY Bender's ® ability to bend 45° beyond ninety (135° PA) is one of its greatest features. Customers buy standard benders and do this simple alteration themselves, adding a degree or two of overbend to the rocker. This easy alteration is done by grinding the bending jaw of the rocker, while not distrubing the working radius of the bending lobe (grind past centerline). For assistance, call READY Technology and we will give you the necessary dimensions to make this alteration ![]() |
Pad Benders
Pad Benders Overview |
N/A
Pads can help in many bender applications. By activating the bender on top of a pad, you isolate the rocker from the part on the critical holddown surface. NO CONTACT = NO MARK Important Pad Functions
When Using Pads, READY Technology Reommends:
![]() |
- 1 To use standard benders, PH should exceed these dimensions. Fax prints for specials.